- Description
Description
AS150 is a balanced mid-high coating grade for aluminized steel tube. With a nominal coating weight of about 150 g/m², it provides a stronger protection margin than lighter grades such as AS80 and AS120. It is widely considered when corrosion resistance, heat exposure, and material cost must be balanced. For exhaust systems, échangeurs de chaleur, and water-heater tubing, the coating level should always be matched to the actual temperature and operating environment.
What Does AS150 Mean?
Le AS number refers to the nominal aluminized coating weight. AS150 generally indicates approximately 150 g/m² of total coating on both sides, subject to the applicable standard and its specified tolerance.
| Grade | Nominal coating weight | Protection level | Typical positioning |
|---|---|---|---|
| AS80 | ~80 g/m² | Moyen | General industrial service |
| AS120 | ~120 g/m² | Medium-high | More demanding environments |
| AS150 | ~150 g/m² | Mid-high | Hot, mouillé, and industrial service |
| AS200 | ~200 g/m² | Haut | More severe exposure |
Coating weight should be stated together with the relevant standard. The AS designation alone should not be used to infer exact local coating thickness or guaranteed service life.
Why AS150 Is a Balanced Workhorse
The main advantage of AS150 is its position between light and heavy coating levels. It adds a meaningful protective reserve without automatically moving to the highest coating category.
Corrosion
A heavier Al-Si coating provides more material reserve than lighter grades under suitable corrosive conditions.
Chaleur
The aluminized surface is designed for applications where elevated temperature is important.
Coût
It can provide a practical middle point when a very heavy coating is not required.
For this reason, AS150 is often a useful mainstream specification for demanding but cost-sensitive tube applications. The correct choice still depends on temperature, humidité, atmosphere, tube design, et durée de vie requise.
AS150 Coating Thickness: About 30–40 μm
Coating weight and coating thickness are related through coating density, but they are not interchangeable specifications. The Al-Si coating also contains an alloyed transition region between the surface layer and steel substrate.
For AS150-level material, a practical indicative coating thickness is often discussed in the range of about 30–40 μm. This is a reference range rather than a universal contractual value. Actual thickness can vary with the coating process, measurement location, et norme applicable.
AS150 for Hot and Wet Service
AS150 becomes particularly interesting when a tube faces both temperature and moisture. The coating helps protect the carbon-steel substrate while providing an aluminized surface designed for elevated-temperature applications.
Cependant, “heat resistant” does not mean that every AS150 tube can operate continuously at any high temperature. Température, exposure time, atmosphere, cyclage thermique, and coating condition must be evaluated together.
The 450°C Reference Boundary
For applications around 450°C and below, AS150 can provide a useful performance margin compared with lighter coating selections when the material is otherwise suitable. The difference should not be interpreted as a universal temperature rating between AS150 and AS80. Actual maximum service temperature depends on the steel grade, système de revêtement, atmosphere, thermal cycle, and application design.
| Condition | AS80 | AS150 |
|---|---|---|
| Dry indoor service | Usually sufficient | More coating reserve than necessary in some cases |
| Mild outdoor exposure | Possible | Higher margin |
| Hot and wet service | Requires evaluation | Often more suitable |
| Around 450°C | Application-specific | Useful reference range, subject to design verification |
| Severe high-temperature exposure | Requires detailed review | Requires detailed review |
The key point is that AS150 provides more coating reserve, not an unlimited temperature rating.
Typical AS150 Tube Applications
The combination of coating protection and heat capability makes AS150 a practical candidate for several industrial tube applications.
| Application | Why AS150 can fit | Key design check |
|---|---|---|
| Exhaust system main tubes | Heat and oxidation protection | Peak temperature, condensat, chimie des gaz |
| Échangeurs de chaleur | Useful balance of coating and corrosion protection | Fluid chemistry and operating temperature |
| Water-heater tubes | Suitable for selected thermal and atmospheric conditions | Water quality, température, condensat, and code requirements |
| Industrial ducts | Higher coating reserve than light grades | Humidity and chemical exposure |
Salt Spray: How Should AS150 Be Compared?
Salt spray testing can show differences between coating systems under controlled laboratory conditions. A heavier coating can provide greater coating reserve, mais salt-spray hours should not be converted directly into years of service life.
For AS120, AS150, and AS200 comparisons, the test method, préparation des échantillons, qualité du revêtement, cut-edge condition, and failure criterion must be kept consistent. Otherwise, a higher reported number may not represent a meaningful material advantage.
| Factor | AS150 implication |
|---|---|
| Higher coating weight | More coating material is available before the substrate becomes exposed. |
| Salt spray result | Useful for controlled comparison, not direct service-life prediction. |
| Real outdoor life | Depends on humidity, sel, pollutants, température, damage, and maintenance. |
AS150 vs AS120 vs AS200: Which Should You Choose?
The choice should be based on the required protection margin rather than simply selecting the largest coating number.
| Grade | Coating level | Best fit | Upgrade reason |
|---|---|---|---|
| AS120 | Medium-high | Moderate corrosion and temperature demand | Use AS150 when more coating reserve is required |
| AS150 | Mid-high | Balanced hot and wet industrial service | Move to AS200 when exposure or specification requires more reserve |
| AS200 | Haut | More severe corrosion or coating requirements | Higher cost and coating amount may not be necessary for mild service |
AS150 Is Not a Universal High-Temperature Solution
Aluminized steel is often selected for heat-related applications, but the coating system has limits. Long-term exposure at elevated temperature can change the coating structure and affect its protective performance.
For exhaust and thermal equipment, buyers should provide the continuous operating temperature, température maximale, heating cycle, atmosphere, and expected service duration. A short peak at 450°C is not equivalent to continuous exposure at 450°C.
Where temperatures move well beyond the intended operating range, a different aluminized grade, heat-resistant alloy, or stainless steel solution may need to be evaluated.
Procurement Checklist for AS150 Tube
Confirm AS150 and the required coating-weight tolerance.
Specify outside diameter, épaisseur de paroi, longueur, and dimensional tolerances.
State continuous and peak temperatures rather than only “high temperature.”
Describe humidity, condensat, sel, produits chimiques, and outdoor exposure.
Define coating-weight testing, inspection des surfaces, dimensional checks, et les certificats requis.
AS150 Tube Supply: Stock and Bulk Orders
For production projects, material availability can be as important as the coating grade. Teda Ganghua supports international buyers sourcing aluminized steel tubes and related coated steel products for industrial applications. Buyers can provide tube dimensions, AS coating level, nuance d'acier, exigences de surface, quantité, and inspection documents.
For recurring production or larger projects, stock availability and bulk-order pricing can be evaluated together. This helps buyers compare the cost of AS120, AS150, and AS200 based on the actual quantity and specification instead of selecting a coating level from price alone.
For project requirements, buyers can review the available tubes en acier aluminisé and provide the required size, coating grade, quantité, and delivery requirements for a quotation.
AS150 Aluminized Steel Tube FAQs
1. What is AS150 aluminized steel tube?
AS150 generally refers to an aluminized coating level of about 150 g/m² total on both sides. The exact value and tolerance depend on the applicable product standard.
2. How thick is an AS150 coating?
An indicative thickness range of about 30–40 μm is often used for AS150-level material, but actual thickness varies. The coating weight and applicable standard should control the purchase specification.
3. Is AS150 suitable for 450°C service?
AS150 peut être envisagé pour des applications autour de 450°C lorsque la nuance d'acier, système de revêtement, atmosphere, thermal cycle, et la durée du service sont adaptées. Il ne doit pas être traité comme une température universelle de 450°C..
4. L'AS150 est-il meilleur que l'AS120?
AS150 offre un poids de revêtement plus élevé et donc une plus grande réserve de revêtement. Il est utile lorsque l'application présente des exigences plus élevées en matière de corrosion ou d'environnement., mais l'AS120 peut être plus économique lorsque son niveau de protection est suffisant.
5. Quand dois-je passer de l'AS150 à l'AS200?
Envisagez l'AS200 lorsque l'environnement de service est plus corrosif, la réserve de revêtement requise est plus élevée, ou les spécifications du projet demandent un revêtement plus épais. La décision doit être basée sur l'exposition réelle et la durée de vie requise.


















