Astm A463 Jis G3314 En 10346 Tubo de aço aluminizado

Descrição

ASTM A463, JIS G3314 and EN 10346 all cover continuously hot-dip aluminium-silicon coated steel, but their designation systems, coating-mass conventions, substrate grades and mechanical requirements are not identical. For aluminized pipe procurement, the safest approach is to compare the complete material definition—substrate grade, Al-Si coating type, coating mass, grossura, forming requirements and applicable tube dimensions—rather than treating one grade code as an automatic equivalent of another.

Key rule: Tipo ASTM A463 1, JIS G3314 AS grades and EN 10346 +AS designations describe related Al-Si coated steel products, but a cross-standard substitution should be approved from the complete specification rather than from the coating number alone.

1. A463 vs JIS G3314 vs EN 10346: What Each Standard Covers

ASTM A463 is the U.S. specification for steel sheet and strip coated with aluminium by the hot-dip process. JIS G3314 covers hot-dip aluminium-coated steel sheet and strip in the Japanese system, including the SA1C, SA1D and related forming grades. EM 10346 is the European standard for continuously hot-dip coated steel flat products and includes aluminium-silicon alloy coating designated by +COMO. EM 10346 therefore contains a broader family of metallic coatings, while +AS identifies the Al-Si coating route within that system. :referência de conteúdo[ovelha:0]{índice=0}

PadrãoMain Product ScopeAl-Si IdentificationTypical Forming System
ASTM A463Hot-dip aluminium-coated steel sheet and stripTipo 1 / Tipo 2Commercial, drawing and deeper forming grades depending on specification
ELE G3314Hot-dip aluminium-coated steel sheet and stripAS coating system with coating-mass designationsSA1C, SA1D and higher forming grades
EM 10346Continuously hot-dip coated flat steel products+COMODX51D–DX57D and other grade families according to application

Important for pipe buyers: these are primarily flat-product standards. If coated strip is roll-formed or welded into tube, the finished tube’s outside diameter, espessura da parede, comprimento, ovality, straightness and weld requirements should be specified separately.

2. Tipo de revestimento: Tipo 1, Tipo 2 and +AS Are Not Interchangeable Labels

One of the most common cross-standard mistakes is assuming that the words “aluminized steel” define the same coating chemistry in every standard. ASTM A463 distinguishes Tipo 1 e Tipo 2; JIS G3314 uses its own Al coating classification and coating-mass system; EM 10346 identifies aluminium-silicon alloy coating with the +COMO suffix.

Para tipo 1 material, the aluminium coating contains silicon as part of the controlled coating chemistry and is widely used where heat resistance and general aluminized-steel performance are required. Tipo 2 is associated with a different aluminium coating formulation and is commonly selected where corrosion and forming requirements call for that specific coating system. The buyer should therefore state the exact ASTM coating type instead of writing only “ASTM aluminized steel.”

How the designations should be read

ASTM: substrate/forming grade + Tipo + coating designation or mass as required.

ELE: substrate/forming grade such as SA1C or SA1D + specified Al coating mass.

EM: substrate grade such as DX51D or DX53D + COMO + coating mass such as AS080, AS100, AS120 or AS150.

EM 10346 explicitly lists +AS as the aluminium-silicon alloy coating symbol and provides AS060, AS080, AS100, AS120 and AS150 coating-mass designations in its coating-mass table. :referência de conteúdo[ovelha:1]{index=1}

3. Coating Weight Comparison

Coating mass is normally expressed as the total mass on both surfaces, but the exact test method, designation and acceptance criteria differ by standard. The following table is therefore a procurement comparison, not a declaration that every number is automatically equivalent across standards.

Aprox.. Total Coating MassASTM A463 ExampleJIS G3314 ExampleEM 10346 +COMO
40 g/m²Tipo 1 T1-13 class is commonly referenced40 g/m²Not an AS designation in the cited EN table
60 g/m²Check exact A463 designation60 g/m²AS060
75–80 g/m²T1-25 is associated with 75 g/m² minimum80 g/m²AS080
100 g/m²Check exact A463 coating designation100 g/m²AS100
120 g/m²T1-40 is associated with 120 g/m²120 g/m²AS120
150 g/m²Verify exact Type and designationVerify exact JIS designationAS150

EM 10346 gives AS coating masses of 60, 80, 100, 120 e 150 g/m² as minimum total coating masses on both surfaces in its coating-mass table. :referência de conteúdo[ovelha:2]{index=2} Industry comparison tables also show why numerical matching alone can be misleading: ASTM designations such as T1-25 and T1-40 use their own acceptance conventions, while JIS and EN use different naming systems. :referência de conteúdo[ovelha:3]{index=3}

4. Substrate Grade Systems: A463 vs SA1C/SA1D vs DX51D–DX56D

The substrate designation is just as important as the coating. A tube that needs roll forming, bending or flaring may require a drawing-quality substrate rather than a commercial-quality grade.

Forming LevelASTM A463ELE G3314EM 10346
Commercial formingCS / commercial-quality family, subject to exact specificationSA1CDX51D+AS
DesenhoDrawing-quality familySA1DDX52D/DX53D+AS
Desenho profundoDDQ / deeper forming categories depending on specificationSA1E and higher forming categories where specifiedDX54D–DX56D+AS
Very high forming demandCheck exact A463 grade and supplementary requirementsUse the applicable higher forming gradeDX57D+AS where available and applicable

EM 10346 lists DX51D through DX57D as forming grades with different mechanical-property windows. Por exemplo, published EN 10346 data show increasing minimum elongation requirements as the grade moves from DX51D toward deeper-drawing grades such as DX54D and DX56D. :referência de conteúdo[ovelha:4]{index=4} Cross-standard comparison tables similarly associate SA1C with commercial quality, SA1D with drawing quality, and SA1E with deeper drawing requirements. These associations should be treated as procurement starting points rather than automatic certificates of equivalence. :referência de conteúdo[ovelha:5]{índice=5}

5. Mechanical Requirements Are Not Automatically Equivalent

A frequent purchasing error is to compare only the minimum tensile strength. Formability depends on the complete mechanical-property window, including yield strength, tensile strength and elongation, and in some deep-drawing applications additional forming parameters are relevant.

PropriedadeWhy It MattersCross-Standard Check
Força de rendimentoResistance to permanent deformationCompare specified range, not only nominal grade name
Resistência à tracçãoUltimate tensile capacityVerify the complete minimum/maximum requirement
AlongamentoGeneral indication of ductilityCheck gauge length and thickness corrections
Forming parametersImportant for deep drawing and severe tube formingSpecify when the application is forming-critical

Por exemplo, EM 10346 data show DX51D with a tensile-strength range of approximately 270–500 MPa and a minimum elongation of 22%, while deeper-forming grades have different strength and elongation windows. :referência de conteúdo[ovelha:6]{index=6}

6. Dimensional Tolerances: Flat Strip vs Finished Pipe

All three standards primarily define the coated flat product. Portanto, a dimensional comparison must distinguish strip tolerance de finished-tube tolerance.

DimensionFlat ProductFinished Tube
GrossuraControlled according to the flat-product standardTube wall-thickness tolerance must be specified
LarguraControlled as sheet/strip widthUsually becomes tube circumference/forming input
DENot applicableTube-standard requirement
OvalityNot a finished round-tube parameterMust be specified or taken from the tube standard
ComprimentoSheet/coil length formatFixed/random tube length as ordered

7. Can ASTM, JIS and EN Materials Be Interchanged?

They can sometimes be technically comparable, but the designation alone does not establish interchangeability. A supplier converting an ASTM requirement into EN or JIS terminology should prepare a documented cross-reference based on at least five parameters:

1. Substrato
Steel grade and chemistry
2. Revestimento
Type and Al-Si chemistry
3. Massa de Revestimento
Total or surface-specific requirement
4. Mechanics
Colheita, tensile and elongation
5. Dimensions
Thickness and finished-tube tolerances

For a pipe application, add a sixth category: forming and welding performance. A material can have a similar coating mass yet behave differently during roll forming, flexão, flaring or welding because its substrate grade and coating system are different.

8. How to Handle a Cross-Standard Order

If a customer specifies one standard but the mill normally produces another, do not silently replace the designation. Use a controlled conversion statement.

Example procurement format:
“Original requirement: ASTM A463, Tipo 1, drawing-quality substrate, specified coating mass. Proposed alternative: EM 10346 DX53D+AS with AS coating mass __ g/m². Supplier shall provide chemical composition, força de rendimento, tensile strength, alongamento, coating-mass test result and tube dimensional inspection for customer approval before production.”

This approach is safer than writing “ASTM A463 = EN 10346” in a purchase order. It records the original requirement and makes the proposed substitution technically reviewable.

9. Common Cross-Standard Mixing Errors

Common ErrorWhy It Is RiskyBetter Practice
Treating AS120 as universally equivalent to every 120 g/m² coatingDifferent standards use different designation and test rulesState standard + coating designation + required mass
Writing “Type 1” without ASTM identificationType terminology is standard-specificWrite the complete ASTM designation
Equating SA1C with DX51D automaticallyForming category similarities do not replace full mechanical and chemical verificationCompare MTC values and contractual limits
Using sheet tolerance as tube toleranceTube forming changes OD, ovality and dimensional controlSpecify finished-tube tolerances separately
Checking only coating weightSubstrate strength and formability can be differentVerify coating + chemistry + mechanics + dimensões

10. Teda Ganghua Cross-Standard Supply Support

For buyers sourcing Al-Si coated tube for automotive, exhaust, aquecimento, appliance or fabrication applications, Teda Ganghua can organize the quotation around the actual technical specification rather than relying on a single standard name. The inquiry can identify the required substrate grade, coating mass, diâmetro externo do tubo, espessura da parede, comprimento, forming route, surface treatment, inspection documents and packaging requirements.

This is particularly useful when a project moves between ASTM, JIS and EN documentation. Instead of treating the three standards as interchangeable labels, the material can be checked parameter by parameter and the final purchase specification can state the accepted standard, grade and inspection basis.

tubos de aço aluminizados can be specified with the required coating system, grau de substrato, tube dimensions and inspection documentation for cross-standard procurement.

11. FAQs

Is ASTM A463 Type 1 the same as EN 10346 +COMO?

They describe related aluminium-silicon coated steel systems, but the designations are not identical. A technical comparison should verify the substrate grade, coating mass, propriedades mecânicas, dimensions and applicable test requirements before substitution.

Is JIS G3314 SA1C equivalent to EN DX51D+AS?

They are commonly compared as commercial-forming grades in supplier cross-reference tables, but that does not by itself establish contractual equivalence. Chemical composition, propriedades mecânicas, coating mass and test requirements should be checked against the actual order specification. :referência de conteúdo[ovelha:7]{index=7}

Does AS120 mean exactly the same thing in every standard?

Não. EM 10346 uses AS120 as a defined Al-Si coating-mass designation. Other standards may express coating requirements differently, so the standard number and complete coating designation should always accompany the nominal coating mass. :referência de conteúdo[ovelha:8]{index=8}

Can I specify an aluminized pipe only by ASTM A463, JIS G3314 or EN 10346?

Not for a complete finished-tube specification. These standards primarily describe coated flat steel. The finished tube should additionally identify OD, espessura da parede, comprimento, ovality, straightness, requisitos de soldagem/formação e critérios de inspeção.

O que deve ser comparado ao mudar de ASTM para JIS ou EN?

Compare o grau do substrato, química/tipo de revestimento, coating mass, força de rendimento, tensile strength, alongamento, tolerâncias dimensionais, formando métodos de desempenho e teste. Para um tubo soldado, verifique também a rota de formação e soldagem.

Astm A463 Jis G3314 En 10346 Tubo de aço aluminizado

Tubo de aço aluminizado para venda