Dx51d+As120 алюминизированная стальная труба
- Описание
Описание
DX51D+AS120 aluminized steel pipe is a material combination worth evaluating when a component has relatively simple geometry but requires a substantial aluminum-silicon coating. The designation combines DX51D, a commercial-grade steel substrate designation under EN 10346, with AS120, a coating designation associated with a nominal combined coating mass of 120 г/м². For straight tubes, flues, furnace protection components, and selected outdoor tubular structures, this combination can offer a practical balance between substrate requirements and coating protection.
The central purchasing decision is straightforward: when a component does not require demanding deep drawing, it may be more economical to select a suitable commercial-grade substrate and allocate more of the specification to coating performance. Однако, the substrate production route, finished-tube manufacturing process, forming severity, and actual operating environment must all be verified. DX51D+AS120 is not automatically suitable for every high-temperature or corrosive application simply because its coating mass is relatively high.
1. Decoding DX51D+AS120: Substrate and Coating
The designation contains two distinct pieces of information. DX51D identifies the substrate grade within the EN coated-flat-steel designation system, while +AS identifies an aluminum-silicon hot-dip coating. AS120 specifies the coating-mass category in the applicable designation context.
| Designation | What it identifies | Procurement significance |
|---|---|---|
| DX51D | Commercial-grade substrate designation under EN 10346. | A starting point for general forming applications, subject to the specified mechanical properties and production route. |
| +КАК | Aluminum-silicon hot-dip coating designation. | Identifies the coating system rather than the substrate’s forming grade. |
| АС120 | Nominal combined coating mass of 120 g/m² in the relevant designation context. | Provides a higher coating-mass option than AS60 or AS80, subject to the applicable specification. |
AS120 normally refers to the coating mass across both sides combined, not 120 g/m² on each side. If distributed evenly, it corresponds to approximately 60 г/м² на сторону. Actual distribution, допуски, test methods, and acceptance criteria should be confirmed in the governing specification and supplier documentation.
Important standards distinction
В 10346 addresses continuously hot-dip coated flat steel products. When DX51D+AS120 is specified for a finished pipe, buyers should confirm the incoming strip specification, tube-forming route, требования к сварке, and finished-product acceptance criteria. The flat-product designation alone does not establish every requirement for the completed tube.
2. DX51D: Commercial Grade Does Not Mean One Identical Production Route
DX51D is commonly used for general-purpose forming of coated flat steel products. Its designation should not be interpreted as a promise of deep-drawing performance. The actual properties available for a particular order depend on the applicable standard, product thickness, production route, and supplier’s guaranteed values.
Cold-Rolled and Hot-Rolled Substrate Routes
DX51D can be produced using different substrate routes, including cold-rolled or hot-rolled base material where permitted by the applicable product specification and manufacturing process. DC51D is commonly associated with a cold-rolled substrate route in commercial descriptions. These labels should not be treated as interchangeable without checking the precise standard and delivery conditions.
Some supplier references compare the quality level of cold-rolled-base DX51D with DC01, and hot-rolled-base DX51D with DD11. Such comparisons can help explain commercial sourcing differences, but they are not universal equivalence rules. The relevant standards, chemical composition, механические свойства, thickness range, and coating requirements must be checked before using these comparisons for technical substitution.
| Purchasing factor | What to verify | Why it matters |
|---|---|---|
| Substrate route | Cold-rolled or hot-rolled base, where applicable. | Can affect surface condition, dimensional characteristics, forming behavior, and commercial price. |
| Mechanical properties | Guaranteed yield strength, tensile strength, удлинение, and applicable test conditions. | Confirms whether the substrate meets the part’s forming and structural requirements. |
| Coating specification | AS120 mass basis, допуски, distribution, and inspection method. | Prevents misunderstandings about coating quantity and acceptance. |
| Finished tube | Outside diameter, толщина стены, длина, weld seam, and dimensional tolerances. | The finished product must meet the application requirements, not just the flat-steel designation. |
Different substrate routes and guaranteed property ranges can contribute to a wide price range for products sold under the same broad commercial designation. When comparing quotations, buyers should confirm the production route and technical requirements rather than judging price by DX51D alone.
3. Why Pair Commercial-Grade DX51D with AS120?
The key idea is to match the substrate to the forming demand and the coating to the service environment. For a straight pipe or a component with limited deformation, demanding deep-drawing properties may not be necessary. A higher coating-mass category may instead be a more relevant part of the specification when the service conditions justify it.
Commercial Substrate
A practical starting point for conventional tube forming and relatively simple component geometry when the verified properties meet the design requirements.
Higher Coating Mass
AS120 may provide more coating material than lower-mass options, making it worth evaluating where additional coating reserve is required.
Application-Led Cost Control
Avoid specifying deep-drawing capability or a heavier coating without a demonstrated need, but do not compromise essential performance to reduce initial cost.
AS120 is often treated as a medium-to-higher coating-mass option in commercial selection discussions. Other commonly encountered AS coating-mass categories include AS60, АС80, АС100, АС120, and AS150, although availability and the exact designation range depend on the supplier and applicable specification.
A heavier coating does not automatically mean proportionally longer service life. Температура, chemical atmosphere, влага, термоциклирование, Адгезия покрытия, and fabrication damage all influence performance. The correct choice should be based on operating conditions and, where necessary, representative testing.
4. Typical Applications for DX51D+AS120 Tubes
This combination is most worth evaluating for parts that have relatively simple geometry but need a specified aluminum-silicon coating. Suitability depends on the actual tube-manufacturing route and operating environment.
| Приложение | Potential reason for selection | Required checks |
|---|---|---|
| Straight tubes and ducts | Limited forming may reduce the need for a higher drawing-grade substrate. | Размеры трубки, weld integrity, сплошность покрытия, and service temperature. |
| Flues and hot-air ducts | May suit selected thermal-airflow applications with qualified exposure conditions. | Continuous and peak metal temperatures, gases, condensate, и термоциклирование. |
| Furnace protective tubes and covers | A coated steel component may be appropriate in a verified furnace environment. | Atmosphere chemistry, actual metal temperature, oxidation requirements, и термоциклирование. |
| Outdoor supports and structural tubes | May be considered where the coating system and structural properties satisfy the design. | Loads, local corrosion exposure, cut edges, joints, and the required service life. |
| General heat-resistant piping | May suit non-pressure or otherwise appropriately designed service within qualified limits. | Pressure code, толщина стены, качество сварки, corrosion mechanism, and inspection requirements where relevant. |
For pressure-containing service, DX51D+AS120 alone does not establish pressure suitability. The design code, material properties, толщина стены, fabrication quality, and inspection requirements must be assessed separately.
5. Forming Limits: When DX51D Is Not the Right Starting Point
DX51D is a commercial-grade designation, not a guarantee of demanding deep-drawing performance. Where the component involves severe drawing, substantial stretching, or complex geometry, a more suitable drawing grade should be evaluated.
Deep Drawing
For deep-drawn parts, consider grades such as DX53D or DX54D, depending on the required drawing severity and the applicable product standard. The selected grade must still be verified against guaranteed properties, требования к покрытию, and the forming process. A higher drawing grade does not by itself eliminate coating damage.
Small-Radius Bending and Expansion
Tight-radius bending, flaring, and expansion can place substantial strain on the coating and substrate. Depending on coating structure, адгезия, оснастка, forming direction, and deformation severity, the coating may crack or become damaged. This is a potential risk rather than an inevitable result for every AS120 product.
Before production, confirm the minimum bend radius and forming sequence with the supplier, and carry out trials using representative material where coating integrity is critical. A lower coating mass or a different substrate may be worth evaluating if it improves the combined forming and service result, but the change must be validated rather than assumed.
6. AS80 vs AS120 vs AS150: Choosing the Coating Level
The best coating mass is the one that meets the operating requirement with an acceptable production and lifecycle cost. Higher coating mass may be appropriate where additional protective reserve is needed, but it can also affect material cost and forming behavior.
| Coating designation | Nominal combined mass* | Selection considerations |
|---|---|---|
| АС80 | 80 г/м² | Evaluate for routine service where this coating level meets the required performance. |
| АС100 | 100 г/м² | An intermediate option where specified and available. |
| АС120 | 120 г/м² | Worth evaluating when a higher coating mass is required for the intended exposure. |
| АС150 | 150 г/м² | Consider where the applicable coating system and service requirements justify the additional coating mass. |
*The values above represent nominal combined coating mass in the relevant designation context. Confirm the applicable standard, допуски, coating distribution, and supplier availability before ordering.
Do not choose AS120 or AS150 solely because a component operates at a high temperature. Aluminum-silicon coatings have application-specific limits, and the surrounding atmosphere can be as important as temperature. For severe oxidation, aggressive chemicals, or long-term extreme-temperature exposure, engineering review and material testing may be necessary.
7. Procurement Checklist for DX51D+AS120 Aluminized Steel Pipe
To obtain comparable quotations and reduce specification gaps, procurement managers should define the following information before placing an order.
- Субстрат: DX51D designation, применимый стандарт, production route where relevant, and guaranteed mechanical properties.
- Покрытие: +AS120 requirement, coating-mass basis, permitted tolerances, and inspection method.
- Размеры трубки: Outside diameter, толщина стены, длина, допуски на размеры, and straightness or ovality limits.
- Manufacturing route: Incoming coated strip, tube-forming method, weld process, and any subsequent forming operations.
- Operating conditions: Continuous and peak temperature, atmosphere, влага, chemical exposure, и требуемый срок службы.
- Quality documentation: Material test certificate, coating inspection results, прослеживаемость, and any project-specific inspection requirements.
- Packaging and delivery: Bundle protection, количество, delivery schedule, and handling requirements that prevent damage during transportation.
For a component with a simple shape, this information helps determine whether DX51D+AS120 is a reasonable specification or whether the design needs a different substrate, покрытие, or tube standard. A clear specification is more useful than relying on a grade name alone.
8. Теда Ганхуа: Aluminized Steel Tube Sourcing Support
Teda Ganghua works with industrial buyers on metal product sourcing and specification review. For projects involving coated tubing, providing the requested grade, coating mass, размеры, метод формирования, рабочая температура, and inspection requirements helps clarify the material scope before quotation.
Explore aluminized steel tubes and submit your drawing or technical specification for review. Teda Ganghua can use the supplied requirements to discuss the requested configuration, identify details that need confirmation, and support a more consistent comparison of available supply options.
For repeat or high-volume orders, buyers should confirm the production route, coating acceptance criteria, размеры трубки, documentation, and delivery requirements together. This helps align material selection with manufacturing needs and avoids relying on coating mass or substrate designation as the sole indicator of suitability.
Часто задаваемые вопросы
1. What does DX51D+AS120 mean?
DX51D identifies a commercial-grade substrate designation under EN 10346, while +AS120 identifies an aluminum-silicon coating category with a nominal combined coating mass of 120 g/m² in the relevant designation context. For finished pipe orders, the tube standard and manufacturing requirements should also be specified.
2. Is AS120 equal to 120 g/m² on each side?
Нет. In the relevant designation context, AS120 normally refers to a nominal combined coating mass of 120 g/m² across both sides. An even distribution would be approximately 60 г/м² на сторону, but the actual distribution and tolerances must be confirmed against the applicable specification.
3. Is DX51D suitable for deep drawing?
DX51D is a commercial-grade designation intended for general forming applications, not a guarantee of demanding deep-drawing capability. For more severe drawing operations, evaluate grades such as DX53D or DX54D and verify their properties and coating performance for the intended process.
4. Гарантирует ли AS120 лучший срок службы, чем AS80??
Не в каждом приложении. AS120 имеет более высокую номинальную массу покрытия, чем AS80., но срок службы зависит от температуры, atmosphere, целостность покрытия, производственный ущерб, и другие условия воздействия. Выбирайте покрытие, исходя из фактических эксплуатационных требований, а не только по массе покрытия..
5. Можно ли использовать DX51D+AS120 для напорных труб??
Само по себе обозначение не определяет пригодность для работы под давлением.. Применимый проектный код, material properties, толщина стены, качество сварки, инспекция, и условия эксплуатации должны быть оценены до того, как материал будет одобрен для применения в условиях высокого давления..



















