+Rivestimento AS vs +Z: Guida all'alluminio-silicio e all'acciaio allo zinco
+AS e +Z non sono denominazioni di rivestimento intercambiabili. Nell'EN 10346 terminologia, +COME identifies an aluminium-silicon coated steel product, Mentre +Z identifies a zinc-coated steel product. Both are continuously hot-dip coated flat steels, but their coating chemistry, metallurgical structure, corrosion mechanisms, temperature behavior, forming considerations and typical applications are different.
The procurement boundary: +Z is a zinc coating system primarily selected for atmospheric corrosion protection, while +AS uses an aluminium-silicon coating system designed for applications where heat resistance and oxidation resistance are important. Choosing between them should therefore start with the service environment rather than the coating appearance alone.
1. +AS vs +Z: The Coating Chemistry Is the First Difference
The most fundamental distinction is chemical composition. A +Z coating is based on zinc, whereas +AS is an aluminium-silicon coating. IN 10346 covers both coating systems within its continuously hot-dip coated flat-product framework, but they are assigned different coating symbols because they provide different performance characteristics.
| Caratteristica | +Z | +COME |
|---|---|---|
| Main coating chemistry | Zinco | Aluminium-silicon |
| Primary protection mechanism | Barrier protection plus zinc sacrificial action | Aluminium-rich barrier and stable oxide protection |
| Resistenza al calore | Limited compared with aluminium-silicon coatings | Better suited to elevated-temperature oxidation environments |
| Typical application emphasis | Protezione generale dalla corrosione | Heat-resistant ducts, exhaust components and thermal equipment |
| Typical procurement concern | Massa di rivestimento, corrosion environment and forming | Massa di rivestimento, temperatura, ossidazione, forming and weld-zone condition |
2. Why Zinc and Aluminium-Silicon Behave Differently
Zinc and aluminium protect steel through different mechanisms.
A zinc coating provides both a physical barrier and galvanic protection. When exposed steel is locally damaged, zinc can act as a sacrificial material because zinc is electrochemically more active than steel. This makes zinc coatings particularly useful where scratches, cut edges and localized coating damage are part of the service environment.
An aluminium-rich coating behaves differently. Aluminium rapidly forms a compact oxide film when exposed to oxygen. That stable oxide contributes significantly to the coating’s resistance to high-temperature oxidation. Silicon is added to the coating alloy to control the coating/substrate reaction and metallurgical structure during hot-dip coating.
This is the first major performance divide: +Z is strongly associated with sacrificial zinc protection, while +AS relies much more heavily on an aluminium-rich barrier and oxidation-resistant surface.
3. The Heat-Resistance Boundary
The distinction becomes especially important when the steel will operate at elevated temperature.
Zinc has a relatively low melting point of approximately 419°C. This does not mean that every zinc-coated component immediately fails at 419°C, because service performance depends on coating condition, atmosphere, exposure time, substrate temperature and the overall component design. Tuttavia, zinc coatings are generally not the first choice when sustained high-temperature oxidation resistance is the primary requirement.
Aluminium-silicon coatings are specifically used where the coating must tolerate substantially higher operating temperatures. The aluminium-rich surface forms a protective oxide layer that slows further oxidation of the coating and underlying steel.
Important:
Do not interpret the coating designation as a universal maximum service temperature. Actual temperature capability depends on continuous or cyclic exposure, atmosphere, coating mass, grado del substrato, component geometry and the required service life.
4. +Z Is Not a Substitute for +AS in Exhaust Applications
Exhaust systems provide a straightforward example of why the two coatings should not be treated as equivalents.
An exhaust component experiences elevated temperature, ciclo termico, oxidation and, depending on the engine and operating environment, condensate and corrosive combustion products. A zinc coating may provide useful corrosion protection at moderate temperatures, but its coating behavior under sustained exhaust heat is fundamentally different from that of an aluminium-silicon coating.
For applications such as exhaust tubing, muffler components, heat shields and hot-air ducts, the engineering question is therefore not simply “Which coating has better corrosion resistance?" È “Which coating mechanism remains appropriate under the actual temperature and atmospheric conditions?"
5. Coating Mass Does Not Mean the Same Thing for +AS and +Z
Another common procurement mistake is comparing coating numbers without first checking the coating symbol.
For zinc coatings, designations such as Z100, Z120 or Z275 refer to coating mass requirements under the applicable specification. For aluminium-silicon coatings, designations such as AS80, AS120 or AS150 similarly indicate coating-mass classes. The numerical values therefore describe coating mass, not a universal temperature rating.
| Example designation | Coating family | What the number primarily indicates |
|---|---|---|
| Z120 | Zinco | Specified zinc coating mass class |
| Z275 | Zinco | Specified zinc coating mass class |
| AS80 | Aluminium-silicon | Specified aluminium-silicon coating mass class |
| AS120 | Aluminium-silicon | Specified aluminium-silicon coating mass class |
| AS150 | Aluminium-silicon | Specified aluminium-silicon coating mass class |
AS120 does not mean 120°C, and AS150 does not mean 150°C. Likewise, a higher coating-mass number should not automatically be interpreted as a higher allowable service temperature. Temperature capability and coating mass are separate engineering parameters.
6. Forming Performance: The Coating Is Part of the Manufacturing Problem
Coating selection cannot be separated completely from fabrication.
When coated strip is roll-formed, bent or drawn into a component, the coating experiences deformation together with the steel substrate. The coating’s hardness, duttilità, spessore, metallurgical structure and adhesion influence how it behaves during forming.
Zinc coatings are widely used in formed sheet products because their coating behavior is well established for many cold-forming applications. Aluminium-silicon coatings also support forming, but their coating structure is different and the forming process must be designed around the specific coated product.
For deep-drawn or heavily formed components, buyers should therefore specify the substrate grade and coating together rather than selecting a coating based only on nominal corrosion performance.
7. Welding Creates Another Performance Divide
When coated flat steel is converted into tube, the weld area becomes one of the most important inspection zones.
Durante la saldatura, the coating near the weld can be affected by localized heat. The behavior of a zinc coating and an aluminium-silicon coating is not identical, so the tube manufacturing route, welding parameters, ventilazione, weld-zone treatment and post-weld requirements should be considered during product development.
Per un tubo saldato, specifying only the original coating designation is therefore insufficient. The finished tube specification should also address weld quality, dimensional control and any requirements concerning the coating around the welded area.
8. Resistenza alla corrosione: Do Not Reduce the Comparison to “Which Is Better?"
The two coating systems should be matched to the corrosion mechanism encountered in service.
- Atmospheric exposure: zinc coatings can provide effective sacrificial protection and are widely used for general corrosion protection.
- Localized coating damage: zinc can provide galvanic protection to exposed steel in suitable environments.
- High-temperature oxidation: aluminium-rich coatings provide a different protection mechanism based on the formation of a stable oxide layer.
- Thermal cycling: coating selection must consider repeated heating and cooling rather than a single peak temperature.
- Condensation: exhaust and ducting applications can experience both elevated temperature and corrosive condensate, making the full operating cycle important.
Consequently, a coating that performs well on an outdoor structural component should not automatically be transferred to a high-temperature exhaust application.
9. How Procurement Should Choose Between +AS and +Z
| Service requirement | Key coating consideration | Specification focus |
|---|---|---|
| General outdoor corrosion protection | Sacrificial zinc protection | Environment, coating mass and expected service life |
| Deep forming | Coating ductility and substrate formability | Grado, forming severity, tooling and surface requirements |
| Hot-air duct | High-temperature oxidation behavior | Temperature profile, coating system and thickness |
| Tubo di scarico | Thermal oxidation and cyclic heating | Dimensioni del tubo, rivestimento, weld condition and service temperature |
| Welded coated tube | Coating behavior around the weld | Welding route, inspection and finished surface condition |
10. Teda Ganghua: Selecting the Coating for the Finished Tube
Teda Ganghua supports procurement of coated steel tubing by separating the grado di acciaio di base, coating designation E finished tube requirements. This is particularly useful when the application combines forming, saldatura, elevated temperature and corrosion exposure.
For buyers sourcing tubi in acciaio alluminato, the inquiry can include outside diameter, spessore della parete, lunghezza, coating mass, forming geometry, bend angle and service temperature. These details allow the coating selection to be evaluated against the actual component rather than treating +AS and +Z as interchangeable surface treatments.
Procurement tip: If the application is an exhaust, hot-air duct or thermal component, state the continuous operating temperature, temperatura di picco, thermal cycling pattern and atmosphere in the inquiry. These details are often more useful for coating selection than simply specifying a coating symbol.
11. The Final Performance Boundary
+Z and +AS should never be treated as two names for the same coating.
+Z is a zinc-based coating system with strong sacrificial corrosion-protection characteristics. +AS is an aluminium-silicon coating system whose aluminium-rich surface provides a fundamentally different barrier and high-temperature oxidation mechanism.
The difference becomes particularly significant when coated steel moves from ordinary atmospheric exposure into exhaust, hot-air, furnace-adjacent or other elevated-temperature service. In those applications, simply increasing zinc coating mass is not equivalent to selecting an aluminium-silicon coating.
The correct purchasing method is therefore to specify substrate + sistema di rivestimento + coating mass + geometria + fabrication route + ambiente di servizio. Once these six elements are defined, the supplier can evaluate the coated steel as an engineered component rather than as a generic coated sheet.
Domande frequenti
What is the main difference between +AS and +Z?
+AS denotes an aluminium-silicon coating, while +Z denotes a zinc coating. Their chemistry and protection mechanisms are different.
Is +AS always better than +Z?
Neither coating should be selected solely on the basis of a general “better” ranking. The appropriate choice depends on corrosion exposure, temperatura, formando, welding and required service life.
Can +Z steel be used for exhaust tubing?
It depends on the actual temperature and service environment. Zinc-coated steel is not automatically equivalent to an aluminium-silicon coated material for sustained elevated-temperature applications, so the operating conditions must be evaluated.
Does AS120 mean the material can operate at 120°C?
NO. AS120 refers to a coating-mass class, not a 120°C service-temperature rating. Temperature capability must be specified and evaluated separately.
What information should be included when ordering coated tubes?
Provide the substrate grade, coating designation, coating mass, diametro esterno, spessore della parete, lunghezza, forming and welding requirements, tolleranze dimensionali, temperatura di servizio e ambiente effettivi.



