AS120 AS150 AS200 アルミめっき鋼管コーティングガイド

AS120 AS150 AS200 アルミめっき鋼管コーティングガイド

AS120, AS150, および AS200 はコーティングマスの指定です。, 温度定格ではありません. アルミめっき鋼管用, the number generally indicates the specified coating mass per unit area, so a higher designation means a heavier metallic coating. This distinction is important in high-temperature applications: increasing coating mass can improve coating durability and provide more material for corrosion protection, but it does not automatically make a tube suitable for a higher operating temperature. The base steel grade, コーティングシステム, atmosphere, tube geometry, 熱サイクル, and required service life must be considered together.

What Do AS120, AS150 and AS200 Mean?

アルミメッキ鋼仕様の場合, として designations are commonly used to identify the coating mass. AS120, AS150, and AS200 therefore represent progressively heavier coating levels. The exact measurement convention and minimum requirements should always be confirmed against the applicable product standard and purchase specification.

学年Nominal coating-mass designationGeneral positioningTypical selection logic
AS120About 120 g/m² total coating massCommon general-purpose levelBalanced coating requirement and forming/processing needs
AS150About 150 g/m² total coating massHeavier coating levelGreater coating reserve where exposure or service demand increases
AS200About 200 g/m² total coating massHeavy coating levelApplications requiring a larger coating allowance, subject to forming and specification limits

The stated coating mass is normally a mass-per-area requirement, not a direct coating-thickness specification. Actual coating thickness depends on coating density and measurement method. Buyers should therefore avoid converting AS120, AS150, or AS200 into a fixed micrometer value without checking the governing standard.

Does a Higher AS Grade Mean Higher Temperature Resistance?

Not by itself. This is one of the most important points when selecting aluminized steel tubes for furnaces, 排気システム, hot-air ducts, オーブン, バーナー, and other elevated-temperature applications.

AS200 does not mean “200°C” and AS150 does not mean “150°C.” The numbers identify coating mass rather than the maximum service temperature.

高温時, the aluminum-silicon coating develops an intermetallic diffusion layer with the steel substrate. The coating can provide strong resistance to oxidation and corrosion, but prolonged exposure, 熱サイクル, mechanical deformation, coating damage, and the surrounding atmosphere all influence actual service life.

AS120 vs AS150 vs AS200 for High-Temperature Service

For high-temperature tube procurement, the selection should start with the environment rather than simply choosing the largest coating number.

AS120

A practical choice where the coating requirement is moderate and the tube is not subjected to unusually severe external corrosion or repeated coating damage. It is also widely used where forming and processing efficiency are important.

AS150

A heavier coating provides additional coating reserve. It can be considered when the environment or expected service duration creates a stronger requirement for coating protection, provided the forming process is compatible.

AS200

The heavier coating level can be specified when additional coating mass is required by the application or purchasing standard. It should not be selected solely because the operating temperature is high.

The Five Factors That Matter More Than the AS Number

1. Operating Temperature

Determine the normal temperature, peak temperature, 露出時間, and frequency of thermal cycling. A tube experiencing short peaks is not exposed in the same way as one operating continuously at an elevated temperature.

2. Atmosphere

Combustion gases, oxygen-rich air, 水分, 塩, sulfur-bearing gases, 凝縮水, and other contaminants can change coating behavior. A material suitable for dry hot air may require a different specification in a corrosive combustion environment.

3. Base Steel Grade

The coating is only one part of the tube system. Base-metal strength, creep behavior, 酸化抵抗, forming characteristics, and thermal expansion must be considered at the intended operating temperature.

4. Tube Processing

曲げ, 切断, フレアする, 溶接, piercing, and end forming can locally damage or redistribute the coating. A heavier coating does not eliminate the need to control coating integrity after fabrication.

5. Required Service Life

Two tubes operating at the same temperature may require different coating levels because their exposure duration, 腐食環境, and maintenance cycles are different.

High-Temperature Application Mapping

応用Main concernCoating selection approach
自動車排気部品Thermal cycling and oxidationSelect coating and base steel together; validate the actual exhaust temperature profile
Hot-air ductsContinuous heat and external corrosionAS120–AS200 may be considered according to exposure and service-life requirements
Oven and baking equipment温度, cleanliness, and coating integrityConfirm the coating and substrate are appropriate for the equipment and contact environment
Industrial heating systemsHigh temperature plus thermal cyclingSpecify operating profile, atmosphere, base steel, coating mass, and testing requirements
General fabricated tubingForming and coating damageChoose the coating level together with bending and welding requirements

What Should Be Written on the Purchase Order?

Writing only “aluminized steel tube AS120” leaves several important variables undefined. A technical inquiry should identify the complete tube specification.

Recommended inquiry information:

How to Choose Between AS120, AS150 and AS200

A simple procurement decision can be organized around three questions:

  1. Is AS120 already sufficient under the applicable specification and service environment? If yes, increasing coating mass may not provide a meaningful benefit.
  2. Does the environment justify additional coating reserve? If exposure is more demanding, AS150 or AS200 can be evaluated according to the required standard and forming conditions.
  3. Is the actual limitation temperature rather than corrosion protection? If the concern is maximum service temperature, changing from AS120 to AS200 may not solve the problem. The base steel and complete material system must be reviewed.

Teda Ganghua Aluminized Steel Tube Supply

泰達江華 supports aluminized steel tube sourcing for applications requiring controlled tube dimensions, 塗装仕様, and customized supply. Procurement can be organized around tube OD, 壁の厚さ, 長さ, coating level, 基材, internal coating requirements, processing, 量, and delivery schedule.

For buyers comparing AS120, AS150, and AS200, Teda Ganghua can help match the アルミメッキ鋼管 specification with the intended service environment rather than treating the coating number as a temperature rating. Submit the required dimensions, coating mass, 動作条件, and applicable standard for a technical quotation.

アルミメッキ鋼管 can be reviewed for different industrial tube requirements and customized procurement specifications.

For a high-temperature tube inquiry, send:

の + 壁の厚さ + 長さ + ベーススチールグレード + AS coating level + 内部コーティングの要件 + 動作温度 + atmosphere + 量 + 適用規格.

FAQs About AS120, AS150 and AS200

Does AS200 mean the tube can operate at 200°C?

いいえ. AS200 refers to a coating-mass designation, not a 200°C service-temperature rating. Maximum service temperature must be evaluated from the complete material specification and application conditions.

Is AS200 always better than AS120 for high-temperature applications?

必ずしもではありません. A heavier coating can provide additional coating reserve, ただし、許容動作温度は自動的に上昇しません。. ベーススチール, atmosphere, 熱サイクル, processing, 必要な耐用年数も重要です.

AS120とAS150の違いは何ですか?

主な違いは指定されたコーティング質量です。, AS150 は AS120 よりも重いコーティング レベルを表します. 適切な選択は、適用される規格と必要な保護レベルによって異なります。.

アルミメッキ管の内側もコーティングすべきか?

内面が高温ガスにさらされた場合, 凝縮水, 燃焼生成物, または他の腐食性媒体, 内部コーティング要件を明示的に指定する必要があります. 外部コーティングの指定が自動的に内部表面を説明するとは考えないでください。.

アルミめっき鋼管のサプライヤーにどのような情報を提供すべきか?

ベース鋼種を提供します, チューブの寸法, 長さ, コーティングの種類と質量, 内部コーティングの要件, 動作温度, atmosphere, 処理要件, 量, 適用規格, および検査書類の要件.

この投稿をシェアする