Ống thép Aluminized DX54D+AS: Cấp, Lớp phủ & Hướng dẫn RFQ

Ống thép Aluminized DX54D+AS: Cấp, Lớp phủ & Hướng dẫn RFQ

DX54D+AS thường được mô tả trên thị trường là “Ống aluminized,” nhưng mô tả này chưa đầy đủ về mặt kỹ thuật. Theo EN 10346, DX54D+AS refers to a continuously hot-dip-coated flat steel product: DX54D defines the formability of the steel substrate, while +AS denotes an aluminum-silicon coating system. Finished aluminized tubes are typically manufactured by forming and welding this coated flat steel. Vì thế, tube specifications must separately define the substrate grade, coating mass, quá trình sản xuất, and dimensional requirements for the finished tube.

1. First Correction: DX54D+AS Is Not a Tube Grade

This distinction is critical when preparing a request for quotation (RFQ) or technical data sheet. TRONG 10346 covers continuously hot-dip-coated flat steel products for cold forming, but it does not establish “DX54D+AS tubing” as an independent tube or pipe grade. [DX54D+AS Lớp ống hoặc thép phẳng tráng? Hướng dẫn đặc điểm kỹ thuật]

Specification LevelWhat It DefinesProcurement Question
DX54DCold-forming steel substrate and mechanical propertiesIs the substrate actually DX54D?
+BẰNG Hot-dip aluminum-silicon coatingWhat coating mass is required?
Tube StandardKích thước ống, dung sai, yêu cầu hình thành và hànWhich tube standard and manufacturing process apply?

Procurement Rule: Never specify only “DX54D+AS tube.” A complete technical purchase order should identify the substrate grade, coating designation and mass, tube manufacturing standard, kích thước, dung sai, yêu cầu hàn, and inspection documentation.

Material Numbers: 1.0306 Và 1.0952

As European standards evolve, older drawings and supplier documents may contain different material numbers associated with the DX54D material designation. Historical documents may reference 1.0306, whereas current documentation may identify DX54D using material numbers such as 1.0952 under updated EN 10346-related documentation. [1.0306 hoặc 1.0952? Giải thích về chuyển đổi số vật liệu DX54D]

When the material number on an older drawing differs from that on a current mill certificate, procurement teams should not automatically treat the materials as different grades. Thay vì, verify the applicable edition of the standard and, where necessary, request a formal equivalence statement or material identification declaration.

2. Decoding DX54D+AS

SymbolMeaningTechnical Significance
DXCold-forming steel designationIdentifies a steel family designed for forming and continuous hot-dip coating
54Deep-drawing grade designationIndicates enhanced formability within the DX steel family compared with general forming grades
DDesignation for flat steel products intended for hot-dip coatingDistinguishes this material designation from other steel product and coating systems
+Coating designator separatorSeparates the substrate grade from the coating designation
BẰNG Lớp phủ nhôm-silicIdentifies an aluminum-based coating system designed to provide resistance to high-temperature oxidation

The same DX54D substrate can be combined with several different coating systems, including zinc, zinc-iron, zinc-aluminum, zinc-magnesium, aluminum-zinc, and aluminum-silicon coatings. Vì thế, replacing +BẰNG with another coating designation is not simply a cosmetic substitution. It changes the coating system and may affect the finished material’s corrosion resistance, khả năng chịu nhiệt, and processing characteristics. [+Lớp phủ AS vs +Z: Hướng dẫn về Nhôm-Silicon và Thép Kẽm]

Gb/T 36399 hot-dip aluminum-silicon coated steel tubeGb/T 36399 Ống thép aluminized

3. DX54D Mechanical Properties: Why It Is a Deep-Drawing Steel

For procurement purposes, the deep-forming performance of DX54D should be evaluated using multiple mechanical indicators rather than elongation alone. Typical requirements include tensile strength, sự kéo dài, plastic strain ratio, and work-hardening behavior, with applicable thickness corrections determined in accordance with the relevant standard. [r90 vs n90 trong Tạo hình kim loại tấm vẽ sâu]

Tài sảnTypical DX54D+AS RequirementsProcurement Significance
Sức mạnh năng suất, ReApproximately 120–220 MPa*Indicates a low-strength substrate with high formability
Độ bền kéo, RmApproximately 260–350 MPaDefines the tensile strength range of the forming-grade steel
Độ giãn dài, A80≥34%*Represents overall deformation capacity
r90≥1.4*Indicates resistance to excessive sheet thinning during forming
n90≥0.18*Indicates work-hardening behavior and strain distribution

*Applicable requirements and permitted values must always be verified against the exact edition of the standard, product thickness, surface quality requirements, and contractual specifications. [a80 r90 n90: Tại sao các yêu cầu về vẽ sâu của máy đo mỏng lại được nới lỏng]

[Bảo hành thép sáu tháng: Tấm cũ có thể vẫn được đóng dấu?]

Thickness Corrections Must Be Specified in the Contract

Formability requirements for thin-gauge material may need to be adjusted. This is particularly important when purchasing material thinner than approximately 0.70 mm. If a specification states only “r90 ≥ 1.4” without identifying the applicable thickness correction, the supplier and buyer may apply different acceptance criteria to the same coil.

Thickness RangeA80 Adjustmentr90 Adjustmentn90 Adjustment
0.50 ≤ t < 0.70 mm−2 percentage points−0.2−0.01
0.35 ≤ t < 0.50 mm−4 percentage points−0.4−0.03
t < 0.35 mm−7 percentage points−0.6−0.04
1.50 < t ≤ 2.00 mm—−0.2—
t > 2.00 mm—−0.4—

The practical lesson is straightforward: never copy thin-gauge formability requirements directly from a general DX54D datasheet without checking the provisions applicable to the specific thickness.

Aluminized steel tube under ASTM A463, JIS G3314 and EN 10346 tiêu chuẩnAluminized steel tubes for sale

4. Thành phần hóa học: Distinguishing the Steel Substrate from the Coating

Đối với DX54D, chemical composition requirements apply to the steel substrate, not the aluminum-silicon coating. Typical maximum values for the substrate include the following:

CVàMnPSAl
≤0.12%≤0.50%≤0.60%≤0.10%≤0.045%≤0.30%

A common specification error is to see a silicon limit for the substrate and assume that it describes the coating composition. It does not. Silicon in the substrate’s chemical composition and silicon used in the aluminum-silicon coating belong to different metallurgical systems and must be evaluated separately.

5. What Does +AS Mean?

The +AS coating is an aluminum-silicon alloy coating, not a pure aluminum coating. Industrial aluminum-silicon coatings typically contain several percent silicon, with compositions containing approximately 10% silicon widely used. This coating system is designed to provide resistance to high-temperature oxidation while maintaining good adhesion and processability.

Loại lớp phủ

Uses an aluminum-silicon alloy rather than pure aluminum.

Typical Silicon Content

Approximately 5–11% silicon in common industrial formulations, depending on the specification.

Common Coating Designations

AS060, AS080, AS100, AS120, and AS150 are commonly used designations.

Ứng dụng điển hình

High-temperature components, exhaust-related products, thiết bị sưởi ấm, and other heat-exposed parts.

AS120 and ASTM A463 Type 1: Compare Coating Mass, Not Just Standards

EN and ASTM coating standards use different designation systems and units. Under the applicable EN coating system, AS120 denotes a nominal total coating mass of 120 g/m² across both surfaces. Loại ASTM A463 1 uses designations expressed in ounces per square foot, such as T1-13, T1-25, T1-40, and T1-60. [EN ASTM JIS ISO Al-Si So sánh tiêu chuẩn thép tráng]

EN Coating DesignationNominal Total Coating MassApproximate ASTM Type 1 So sánh
AS06060 g/m -métBelow T1-25
AS08080 g/m -métClose to the T1-25 range
AS120120 g/m -métClose to T1-40, approximately 122 g/m -mét
AS150150 g/m -métBetween T1-40 and T1-60

Important: These are comparison values, not automatic declarations of material equivalence. The coating chemistry, test method, minimum values, designation rules, and application requirements must still be verified against the applicable standard. [Hướng dẫn về lớp phủ AS060 vs AS080 vs AS100 vs AS120 vs AS150]

AS120 Coating Thickness: A Useful Engineering Estimate

If a total coating mass of 120 g/m² is distributed equally across two surfaces, each side accounts for approximately 60 g/m -mét. Using an approximate density of 2.7 g/cm³ for an aluminum-based coating gives a theoretical single-side thickness of roughly 22 mm. This calculation is intended as an engineering estimate only. Actual coating thickness and distribution should be established using the applicable coating-mass test method and supplier documentation.

6. Deep Drawing: Why DX54D Is Suitable for Complex Forming

DX54D is intended for demanding cold-forming applications. Its forming behavior depends on the combined effects of elongation, plastic anisotropy, and work-hardening characteristics.

IndicatorWhat It ControlsWhy It Matters in Tube Production
A80Overall elongation capacitySupports forming without premature tensile fracture
r90Resistance to localized thinningImportant during deep drawing and severe cross-sectional deformation
n90Work-hardening behaviorInfluences how deformation is distributed throughout the forming zone

Another procurement consideration is resistance to stretcher strains. Surface strain marks can become a quality issue for components where appearance is important. For deep-drawing applications, material age should therefore be managed alongside mechanical properties and surface-quality requirements.

Where a supplier provides a defined aging or surface-quality guarantee period, the contract should state that requirement explicitly. Older stock should not automatically be considered equivalent to freshly produced material simply because the nominal grade remains unchanged.

7. The Critical Issue in Tube Manufacturing: Coating vs. hàn

Converting coated flat steel into tubing introduces a processing challenge that does not arise in exactly the same way when the product remains flat sheet: the aluminum-silicon coating interacts with the welding process.

Manufacturing StagePotential IssueProcurement Requirement
Welding ZoneThe coating may affect weld-pool behavior and weld qualityDefine the welding procedure and treatment of the weld zone
Phương pháp hànProcess parameters must account for the coated steel substrateSpecify a qualified welding procedure and applicable consumables
Post-Weld ProtectionCoating removed or affected by heat may leave areas with reduced protectionDefine local protection or coating-repair requirements
Tube FormingSevere bending or expansion may place stress on the coatingVerify coating adhesion after forming
Cut EdgesExposed steel edges have less coating protectionSpecify edge condition and any required sealing or protection

Engineering Focus: For welded aluminized tubing, substrate selection is only one part of the corrosion-performance equation. The weld zone, cut edges, forming radius, and post-processing protection can determine the actual service performance of the finished tube.

8. Cross-Standard Comparison: Do Not Match Designations by Name Alone

SystemTiêu chuẩnTypical DesignationProcurement Note
EuropeanTRONG 10346DX54D+ASCoated flat steel product; the tube standard must be specified separately
Historical EuropeanEarlier EN specificationsDX54D+AS with historical material referencesOlder drawings should be checked against the current edition of the applicable standard
AmericanASTM A463/A463MKiểu 1 Al-Có; T1 coating designationsKiểu 1 và loại 2 are different coating systems
JapaneseJIS G 3314SA1C / Sa1d / SA1EVerify the grade, coating mass, và dự định ứng dụng
InternationalISO 5000Al-Si-coated cold-rolled carbon steel flat productsCheck the exact mechanical and coating requirements

The correct sequence for cross-standard comparison is substrate grade → coating chemistry → coating mass → mechanical requirements → dimensions → test method. A Type 1 Al-Si coating should not be considered interchangeable with a Type 2 pure-aluminum coating simply because both are described as aluminized steel.

9. Typical Applications and Selection Limitations

Automotive Exhaust Components

Suitable for applications requiring formability combined with resistance to high-temperature oxidation and atmospheric corrosion.

Aluminized Tubes and Fittings

Useful where coated steel tubing is required for exhaust systems, thiết bị sưởi ấm, or other temperature-exposed applications.

Heating Equipment

Applicable to selected oven, lò nung, heat-shield, and heat-exchanger components.

HVAC and Industrial Enclosures

Can combine cold-forming capability with atmospheric corrosion resistance in selected applications.

When Should DX54D+AS Be Reconsidered?

  • Extremely high service temperatures: Verify the actual continuous and cyclic operating temperatures rather than relying on generic statements about coating temperature resistance.
  • Severe chloride or chemical exposure: Evaluate the complete corrosion environment and compare alternative material systems.
  • Primary load-bearing structures: The low-strength deep-drawing substrate is not automatically suitable for structural applications requiring high yield strength.
  • Highly visible surfaces: Establish surface-quality, hình thành, and weld-zone requirements before production.
  • Severe post-forming operations: Confirm coating adhesion and the permissible forming radius before selecting the coating mass.

10. DX54D+AS Tube Specification: Complete RFQ Checklist

A professional aluminized tube specification should distinguish material requirements from finished-tube requirements. The following checklist can be incorporated into an RFQ:

MụcRequired Information
1. chất nềnDX54D and the applicable EN 10346 sự chỉ định
2. Lớp phủ+AS and the exact coating mass designation, such as AS060, AS080, AS100, AS120, or AS150
3. Coating-Mass ConventionClearly specify the total mass across both surfaces or the applicable alternative measurement convention
4. Tính chất cơ họcRe, Rm, A80, r90, and n90, including applicable thickness corrections
5. Thành phần hóa họcHeat analysis and material certificate requirements
6. Tube DimensionsOutside diameter, độ dày của tường, chiều dài, ovality, and dimensional tolerances
7. Phương pháp sản xuấthình thành, hàn, and any subsequent tube-forming operations
8. Weld RequirementsWelding procedure, weld inspection, and treatment of the coated zone
9. Edge ProtectionProtection requirements for cut edges and weld areas
10. Chất lượng bề mặtSurface class, permissible defects, and coating adhesion requirements
11. Material AgeApplicable forming-quality or aging-guarantee requirements
12. Inspection DocumentationMechanical, hóa chất, coating-mass, độ bám dính, và hồ sơ kiểm tra kích thước

11. Three Contract Clauses That Prevent Common Disputes

Dispute 1 — Thin-Gauge Material Fails a Formability Test.
Cause: The contract copied a nominal r90 or n90 requirement without incorporating the applicable thickness adjustment.

Dispute 2 — Coating Mass Does Not Match Between Supplier and Buyer.
Cause: One party interprets the value as the total coating mass across both surfaces, while the other uses a different unit or measurement convention.

Dispute 3 — Older Stock Develops Forming or Surface-Quality Problems.
Cause: Material age was not controlled, even though the application requires reliable deep drawing and freedom from surface strain marks.

The simplest way to prevent these disputes is to attach the applicable standard requirements and exact acceptance methods to the purchase order rather than relying on a short material designation.

12. Teda Ganghua Support for Aluminized Steel Coil and Tube Projects

Teda Ganghua can support procurement teams sourcing coated steel for exhaust, sưởi ấm, HVAC, thiết bị, and tube-manufacturing applications. For a DX54D+AS project, procurement can be organized around the substrate grade, chỉ định lớp phủ, coating mass, độ dày, chiều rộng, yêu cầu hình thành, kích thước ống, quá trình hàn, and inspection documentation.

For projects in which coated steel is purchased in coil form and subsequently converted into welded tubing, it is particularly important to evaluate the flat-product specification together with the downstream tube-manufacturing process. Teda Ganghua can coordinate material requirements for cuộn dây thép nhôm applications and help procurement teams define the required coating grade, kích thước, yêu cầu hình thành, and documentation before order confirmation.

This approach reduces the risk of receiving material that matches the stated material designation but does not meet the actual requirements of tube production. For engineering and procurement teams, the objective should always be to establish a complete material-to-tube specification rather than simply copying a single grade designation into the purchase order.

13. Final Engineering Takeaways

DX54D+AS combines a low-carbon steel substrate with a hot-dip aluminum-silicon coating and is intended for deep-forming applications. Its value lies in the combination of formability and high-temperature coating performance, but the designation itself does not define the finished tube. [Chuyển đổi khối lượng lớp phủ: Giải thích một mặt và hai mặt]

To ensure reliable procurement, divide the specification into four levels: DX54D substrate → +AS coating → coating mass → finished-tube manufacturing standard. Then add thickness-dependent mechanical requirements, điều khiển hàn, edge protection, surface acceptance criteria, material-aging requirements, and inspection documentation. [Hàn ống thép Aluminized: Loại bỏ và sửa chữa lớp phủ]

[Ngăn chặn rỉ sét ống thép Aluminized tại các mối hàn và các cạnh cắt]

The most important procurement rule is simple: match the complete technical specification, not just the material code.

[Thép Aluminized và thép không gỉ Ferritic cho hệ thống xả]

Câu hỏi thường gặp

Is DX54D+AS a tube grade?

KHÔNG. It refers to a continuously hot-dip aluminum-silicon-coated flat steel product under the relevant EN standard. Finished aluminized tubes are manufactured from coated flat steel, so the tube standard and manufacturing requirements must be specified separately.

What does +AS mean?

+AS denotes an aluminum-silicon coating, not a pure aluminum coating. The coating chemistry and coating mass must be specified separately from the DX54D substrate grade.

What is AS120?

AS120 is a coating designation indicating a nominal coating mass of 120 g/m² under the applicable EN coating system, generally referring to the combined mass on both surfaces. Its coating mass is approximately comparable to ASTM A463 Type 1 T1-40, but the two designations should not be considered fully equivalent.

Why are thickness corrections important for DX54D?

Deep-forming properties, including elongation, r90, and n90, may be subject to thickness-dependent adjustments. The applicable corrections should be included in the procurement specification so that the supplier and buyer apply the same acceptance criteria.

What is the main issue when converting DX54D+AS into tubing?

The welding and subsequent forming operations must be compatible with the aluminum-silicon coating. The weld zone, cut edges, và các khu vực được hình thành nhiều có thể yêu cầu các biện pháp xử lý cụ thể và bảo vệ cục bộ để duy trì hiệu suất dịch vụ dự định.

DX54D+AS có thể sử dụng cho hệ thống ống xả ô tô không?

Nó có thể phù hợp với các thành phần khí thải và nhiệt độ cao đã chọn khi khả năng định dạng và hiệu suất lớp phủ nhôm-silic của nó đáp ứng nhiệt độ thực tế, ăn mòn, hàn, và yêu cầu về tuổi thọ sử dụng. Môi trường vận hành hoàn chỉnh cần được đánh giá trước khi vật liệu được phê duyệt.

 

Chia sẻ bài đăng này